Hydrom Instruction
ContactShopDeutsch
  • Introduction
    • Charging the Hydrom
    • Turn on the Hydrom
    • Start in Configuration-Mode
    • Access to the user interface
    • Connect to existing WiFi
    • Do PlainWaterCalibration
    • To set up the Hydrom as an MQTT publisher
    • Connect the Hydrom to Ubidots
    • Connect the Hydrom to Brewblox
    • Connect the Hydrom to Brewfather
    • Connect the Hydrom to Grainfather
    • Connect the Hydrom to Telegram
    • Send Measurements via Webhook
    • Connect the Hydrom to BierBot Bricks
    • Connect the Hydrom to Google Sheets
    • Connect the Hydrom to iRelays Display
    • Connect the Hydrom to Brewers Friend
  • Getting Started
    • Disinfect before use
    • Warnings (read before use)
    • Establish first connection to the hydrom
    • Indicator LEDs
  • Other settings
    • Changing the Hydrom name
    • Customize units
    • Factory Reset
    • Adjust Intervall
    • Activate headstand detection
    • Setting up the temperature compensation
  • Calibration
    • Check calibration status
    • Attitude Sensor Calibration
    • Calibration process
      • Manually change the formula
      • Reference method
  • Bluetooth Settings
    • IOS App
  • Troubleshooting
    • An Internet service does not receive any data
    • The Hydrom user interface cannot be accessed.
  • Firmware
Powered by GitBook
On this page
  • Step 1: Open the Menue
  • Step 2: Select "Settings"
  • Step 3: Change device name
  • Save Settings

Was this helpful?

  1. Other settings

Changing the Hydrom name

PreviousIndicator LEDsNextCustomize units

Last updated 1 year ago

Was this helpful?

ATTENTION! If you have entered incorrect Name for the Hydrom, you will not be able to connect to the Hydrom via existing Network. You will then need to use the Configuration-Wifi.

If the setting is incorrect, you can reset the Hydrom as described here:

Changing the Hydrom name has the following effect:

  1. The user interface is not accessed via as described in the chapter, but now via http://<own_choosen_name>/.

  2. Some of the services described in the chapter "Connect Services" now send to a different address.

    However, this is mentioned separately in the respective instruction article.

To make this setting you must have access to the user interface. If this is not the case, see here how to do it:

Access to the user interface

Step 1: Open the Menue

To access the menu bar you have to click on the three lines in the upper left corner. (See arrow) Then the menu bar will open.

Step 2: Select "Settings"

On this page, you can adjust various settings to personalize your experience with the device. Options you can customize include the interval at which the device collects and sends data, the units displayed on the main page, and the overhead detection feature. You can also enable temperature compensation to ensure accurate measurements. Take some time to explore the various settings available and make the necessary adjustments for your needs.

Step 3: Change device name

To change the device name, enter the new name under the "Devicename" lettering. By default, the device name is "Hydrom001".

Save Settings

Saving the data is important because it is the only way to connect to the service after waking up from DeepSleep.

You can check whether the saving was successful by looking at the settings file at http://hydrom001/settings.json/. to check if the save was successful. This file is the permanent memory of the Hydrom.

A second way to check the saving is to reload the page (all browsers offer this). If the properties are then reloaded, the hydrom has accepted them, otherwise the old settings are reloaded.

http://hydrom001/
Reset by the button
#connect-to-the-hydrom-via-browser
access the menu bar by clicking the three lines in the upper left corner
Changing the device name of the hydrometer
Pressing the "save" button saves the settings.